10CAG/10CHG/10CGGHz CHANNEL RADIO CONTROL SYSTEM INSTRUCTION MANUAL Technical updates and additional programming examples. Instruction manual • Read online or download PDF • Futaba 10CG GHz User Manual. Futaba 10CHG Pdf User Manuals. View online or download Futaba 10CHG Instruction Manual.

Author: Gotaxe Vudot
Country: Sri Lanka
Language: English (Spanish)
Genre: Finance
Published (Last): 11 June 2008
Pages: 165
PDF File Size: 16.61 Mb
ePub File Size: 17.60 Mb
ISBN: 129-9-90834-379-6
Downloads: 82164
Price: Free* [*Free Regsitration Required]
Uploader: Tosho

As with all radio frequency transmissions, the strongest area of signal transmission is from the sides of amnual transmitter’s antenna.

Comments to this Manuals Your Name.

If in doubt, return the receiver to our service center for service. V-TAIL mixing is used with v-tail aircraft so that both elevator and rudder 10hcg are combined for Press DIAL to select the actual function you wish to edit from the menu.

Open an unused programmable mix. Charger The initial charge, and any charge after a complete discharge, should be at least 18 hours to ensure full charge.

Area Selection Frequency Range: Other Equipment Gear Doors: May also be used creatively to create a delayed servo on a futaha function mnual www. Copying the information to the model memory of a T10C transmitter. Offsets For an example of trim settings, please see the following: With programmable mixing, could utilize CH5 as the 2nd elevator servo.

When you COPY one model memory over another, everything is copied, including the model’s name.


Additionally, while many peripheral devices will operate in either the high speed or normal mode, some will not. There are 3 basic wing types in aircraft models: Keep the antennas away from the motor, ESC, and other noise sources as much as possible. The coaxial part of the antennas does not need to follow these guidelines, but do not bend it in a tight radius. Internet rutaba is available at no charge at most public libraries, schools, and other public future reference, and can be accessed at any hour of the day, night, weekend or holiday.


For an example of trim settings, please see the following: Any technical there, please see the end of our F. Place the transmitter mxnual the receiver close to each other within one 1 meter. Those are mechanical changes that must be done by a service center. View numerous 110chg mix setups: A few are listed here. Although your 10CG protects the model memories with non-volatile EEPROM memory which does not require periodic replacement and not a battery, the transmitter still should have regular checkups for wear and tear.

Even if there is no servo damage, excess battery drain will result. Press DIAL again to accept the change. Mznual “Power Down Mode” continues for 90 seconds and after that the power will return to the normal level. WARNING After the linking is done, please cycle receiver power and check if the receiver to be linked futzba really under the control by the transmitter to be linked. For details on setting up a complex aerobatic plane, please visit www.

FUTABA 10CAG Instruction Manual

For more information on CAMPacs, please see p. Curves are separately adjustable for normal, idle-up 1, idle-up 2, and idle-up 3. The receiver begins the linking operation. Those functions which are identical to the ACRO setups are referred directly to those pages. Turn off the receiver. If there is an objectionable buzzing sound coming from a servo, there is probably too much resistance in the control. Keep holding the switch for more than one 1 second.


Other functions you may wish to set up for your model. The outputs for other channels indicated below allow to use any type of servos as the frame rate of these outputs are still 14ms on the High Speed mode.

Data cannot be converted from 8U or 9Z memory types. Repeat the prior steps to complete naming the model. If this product is then re-exported futabaa other countries, it may be subject to restrictions on such export. A single long beep.

The T10CG has 15 model memories, which can each support: Set up additional programmable mixes, ex: Setting up the Normal Flight Condition Then press the Dial to choose that function. View additional setups on the internet: It is not intended for use in any application other than the control of models for hobby and recreational purposes.

Upon completion, it cannot be recovered.

Futaba 10CG GHz User Manual | pages

The blue RF light also goes out. The movement is largest at idle and disappears at high throttle to avoid accidental dead sticks. Table of Contents Futaa to nanual manuals Add. If there are some FASST transmitters turned on near the receiver, the LED may show the above status for a brief moment before changing to the status indication as shown in the “LED indication” table above. The 10CG may be master or student with any Futaba transmitter compatible with the cord.

Do not fly when this message is displayed: